樹脂吸附式干燥的機

◆品牌亮點 Product features

※擁有動態平衡相一致的吸氣壓強和露點

1.降解塔之程度與直經經實驗室導致精密機械計算出來，塔床壓力降小，有保障了縮減實驗室氣體干燥的劑5秒的觸碰日子，能夠滿足樣品氣的露點想要。

2.30％的皮膚變干劑加工余量，中用賠償皮膚變干劑的那自然氧化，事關皮膚變干。

3.大型的外擴散器，確保安全生產氣旋粗糙利用烘干劑層，去掉溝流狀況。

※降解氣量消耗的資金高于14％

1.優質的機筒制作，保管100％的過濾室溫，儲放的室溫采用增高恢復的階段的恢復氣室溫，提供裝備的解吸程度，會使恢復更徹底。

2.皮膚干燥和復蘇主要包括反相熱對流實施方案，濕的空氣走過干的氣體吸附劑時限果更佳。復蘇氣出口量含濕量操縱在亞飽和形態形態，使消音器原理器及排氣管短信通道無起霜之慮。

3.可結合干燥處理機的作業環境下各種需求調節器降解氣需求量，有效確保降解空氣多次比較穩定，降解學習壓力低至臨界值。

※干燥處理劑實用壽命短長

1.剛好合適的機筒的尺寸，使氣體借助干劑層的氣速和時段保持著好的情況下，充分地發揮出干劑的的性能。

2.節省的體統分配，在氣體流動加入機筒前，經除油治療立刻除去氣體流動中內含油份物與重廢棄物物，應對變干劑層受廢棄物。

※機運用了大氣高產品質量定時及氣動系統閥和靠得住的全電子無線可程序編寫序管控器，人與機器網頁友誼，定時接連表現雙塔生產，配置時期場地可編，出廠檢驗報告調整10min。蝶閥使用期超過50萬次舞蹈動作。

※筒節壁上作冷鍍鋅鋼防起繡整理，10年不脫漆。

※操作的準確度、機械性能固定、操作的便捷，裝置就不需要前提。

※Bend it out on the same has the stable pressure and dew point

1. The height and diameter adsorption tower by the experimental results calculated precisely, tower, ensure the small resistance bed compressed gas desiccant 5 seconds contact time, meet the requirements of the finished product angry dew point.

2.30% of the surplus, desiccant used to compensate for the natural aging, ensure desiccant dry.

3. Large diffuser, ensure uniform through the desiccant air layer, eliminate channel flow phenomenon.

※Bend the gas loss less than 14% renewable

1. Excellent barrel design, save 100% of the adsorption quantity of heat, storage quantity of heat is used to increase the regeneration stage again angry temperature, improve equipment desorption ability, make renewable more thoroughly.

2. Dry and regeneration of the reverse convection scheme, wet air through the dry when the adsorbent best effect. Getting angry export moisture content control in the saturated state, the muffler and exhaust passage without concentrations of condensation.

3. According to the operation of the dryer load demand adjust dosage, ensure again angry for stability, regeneration renewable air pressure low to critical.

※Bend desiccant long service life

1. The right of barrel size, make the gas through the desiccant flow velocity and time of layer be the best, give full play to the desiccant performance.

2. The reasonable system configuration, in the air into the barrel, except by the efficient before oil processing timely removal in the air in content and heavy oil pollutant, avoid desiccant layer contamination.

※The equipment adopts bend novel high quality and pneumatic valve electric and advanced and reliable full electronic programmable controller, friendly interface, automatic continuous display of the twin towers, working cycle, the programmable factory set 10 min. The valve life for 500000 times action.

※Bend the cylinder body wall be cold galvanizing antirust processing, 10 years don't rust.

※Bend action, stable performance, accurate, easy operation and installation with no need of foundation.

◆包括技巧產品參數 Main technical parameters